How To Change The Bit On A Dewalt Drill

Download Article

Ability drills are super handy and versatile, but you need the correct drill bit for the task. If you're not sure how exactly you're supposed to alter out one drill flake for some other, don't worry! We'll walk y'all through it step-past-pace, whether you have a keyless drill or a keyed chuck drill. The process is surprisingly easy either manner. In but a few minutes, yous'll be ready to start drilling.

ane
Loosen the chuck. The chuck is slice on the end of the drill that loosens and tightens to hold the bit. Grasp the chuck with i paw while you lot hold the handle of the drill with your other hand. Twist the chuck counterclockwise to loosen it. Another option is to pull the trigger gently while holding the chuck.^[1]
- Loosening the chuck will open up the jaws that clench onto the drill bit.
ii

Remove the bit. Once you loosen the chuck, the drill scrap that yous currently have in the drill will start to wobble. You should be able to hands pull it out of the drill in one case the jaws that clamp information technology to the drill are loose.^[ii]

Always inspect the bit when you remove. If it looks damaged or worn, throw information technology out so you don't accidentally use it again later.

Advertisement
3
Fix the bit. Hold the bit with your pollex and index finger so that the smooth part of the bit (the shank) is facing the jaws of the chuck. Insert the flake into the chuck and immediately pull it back towards you about a centimeter.^[3]
- Go along your fingers on the chip and the chuck since the bit isn't secured and could fall out.
iv

Squeeze the trigger. Tighten the bit into place by giving the trigger a few short squeezes. Your other hand should still be loosely holding the flake in place while you do this.^[iv]

Lightly hold the scrap while squeezing to ensure that the bit is installed straight.
v

Engage the ratcheting mechanism if needed. If your drill has a ratcheting mechanism to apply actress pressure to the shank of a drill scrap, you'll need to click it into identify. To appoint it, firmly twist the ratcheting mechanism next to the chuck in a clockwise motion.^[5]

Advertisement

1
Insert the chuck key. If your drill came with a chuck cardinal, you'll need to utilize this in gild to loosen the chuck. The end of the drill key will look like a cog that has teeth. To insert the chuck cardinal, line upward the teeth so that they match the teeth on the chuck and insert the tip into one of the holes on the side of the chuck.
- Many drills that use a chuck key accept a secure place on the drill where y'all tin can store the key.
- Typically you'll come across a key chuck on a power drill rather than a cordless model.
2

Plow the chuck key counterclockwise. As y'all plough the central, the jaws on the chuck will begin to open. Continue turning until the chuck opens enough to easily slide the drill bit out. }

The jaws are the three or four pieces in the mouth of the chuck that extend to concur the scrap in place.
three
Remove the chip. Pull the bit out using your thumb and alphabetize finger once the chuck is loosened. If the chuck is opened wide and y'all plough the drill face up down, it may just fall out.
- Inspect the bit once you lot've removed information technology. Bank check for damage or worn areas. If the bit is dull, you should replace it. If it's bent or shows signs of smashing, throw it out then you won't mistakenly employ it once more.
iv
Insert a scrap. While the jaw on the chuck are open broad, insert your new fleck. Hold the fleck with your thumb and index finger so that the polish office of the scrap (the shank) is facing the jaws of the chuck and insert information technology.^[6]
- Continue your fingers on the chip and the chuck since the bit isn't secured and could fall out.
5
Tighten the chuck. While holding the bit in identify with one hand, plough the chuck key clockwise to tighten the chuck'south jaws with your other hand. Brand sure to tighten information technology firmly so that the bit is secured. Remove the chuck central.^[7]
- Remove your hand from the bit and plow on the drill to examination it before using it.
Advertisement

Add New Question

Question

My chuck key won't turn. How should I fix this?

Marker Spelman is a General Contractor based in Austin, Texas. With over 30 years of structure experience, Mark specializes in constructing interiors, projection management, and project interpretation. He has been a construction professional person since 1987.

Structure Professional

Expert Respond

Applying a little WD-40 or some other lubricating agent can help a still key movement.
Question

How practice you loosen a drill bit?

Jason Phillip is a handyman specializing in mounting and hanging objects onto walls. With over five years of experience professionally mounting and installing objects through his company, Jason's Handyman Services, Jason's work includes working with mounting window AC units, designing art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Top Pro" every yr since 2016 by Thumbtack for beingness 1 of the highest-rated, near popular professionals on Thumbtack.

On almost all drills these days, you just turn the front of the drill to loosen up the drill bit in order to supplant information technology.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Go along the chuck key with the drill or in a safe identify. If you lose your chuck key, you can buy generic replacement keys that come in a diversity of sizes to match your chuck.

Advert

Things Yous'll Need

Ability drill
Replacement bit
Chuck key (if needed)

Near This Article

Commodity Summary 10

To change a drill bit on a keyless drill, twist the chuck counterclockwise to loosen it, then pull information technology out. Hold the new scrap with your thumb and alphabetize finger, then insert it into the chuck. Clasp the trigger a few times to tighten the chip into place, then twist the ratcheting mechanism side by side to the chuck in a clockwise motion. If your chuck has a key, insert the key and turn it counterclockwise, then slide the scrap out. Insert the new bit and turn the key clockwise to tighten the chuck. To larn more than from our Full general Contractor co-writer, like how to tell if a drill bit is worn or damaged, keep reading the article!

Did this summary aid you?

Cheers to all authors for creating a page that has been read 467,558 times.